Sweden?s energy consumption is divided into three major sectors. One of them is the industry sector. One third of Sweden?s energy consumption is converted in the industries.

This thesis concerns an energy audit of a food industry. The company's business consists of boiling and peeling shrimps, and producing mayonnaise-based salads. This type of work involves energy-intensive processes, such as steam generation, compression of air and refrigeration of large spaces. These needs are supplied with electricity. Furthermore, the industry is a major consumer of district heating, particularly for heating the supply air in the ventilation system.

In today?s society there is an increasing demand for renewable energy sources such as sun and wind power. These sources are intermittent, and energy storage is therefore needed to ensure a constant power supply. This report compares pumped hydro energy storage (PHES), compressed air energy storage (CAES), flywheels, batteries, super magnetic energy storage (SMES) and hydrogen energy storage.The opportunities for further development are limited for PHES and CAES in comparison with the other technologies. Lithium-ion batteries and hydrogen energy storage are considered to have the most potential in the future.

Since the turn of the millennium a sharp increase in the interest for bio energy has been observed. Important reasons for this growing interest can be due to the fact that fossil fuels are a finite resource. A net discharge of greenhouse gases occur when fossil fuels are burned. The discharge of greenhouse gases are considered to be the main reason to the greenhouse effect. Means of control to increase the use of bio energy has been introduced and, as intended, the use of bio energy has increased. As a result of the legal provisions the ability to pay for bio energy has increased, which the forest industry view as a problem.

The construction industry has demands on energy use in permanent buildings. How much energy that is permitted to use during the time the building is produced has no requirements. The purpose with this study is to learn how far Skanska has come with the work of making the building site more energy efficient.A literature study has been performed in the beginning of the study to survey what energy efficient arrangements that can be applied and how they operate. Using site visits and interviews the situations on the building sites have been studied as well as the energy efficient measure that are in use.Skanska has come a long way with the work of energy efficient building sites and they keep improving. They have improved half of their cabins so they use 50 % less energy.

The society strives for sustainable development, in the construction industry it is expressed through sustainable building. Energy and LCC analyzes increases the ability to make conscious decisions in the process. A problem in the construction industry is that energy and LCC analysis is not used to the desired extent, as they are perceived as complicated and time consuming. The report aims to achieve a more sustainable building through increased use of energy and LCC analyzes.The goal is to show how BIM can be used to improve the efficiency of the energy and LCC analyzes.The study was conducted with a literature review and a case study to answer which information that is required in a BIM model to perform energy and LCC analyzes. The study also shows which software can be used in BIM based energy and LCC analyzes and how the analyzes can be carried out efficiently.The result shows that effective analyzes may be performed if the BIM-model contains the relevant information for making analyzes.

This diploma work addresses the question of how much energy is spent whenmanufacturing the components of a building as well as of how much energy is used inthe production of a building. The object of the studies is BioCentrum at the SwedishUniversity of Agricultural Sciences in Ultuna just outside the city of Uppsala. The aimof the work was to investigate how much energy was consumed when manufacturingand production in relation to the management, how many years the production wasrepresented. It was also a study in how mature the construction industry is to answerhow much energy was consumed in manufacturing.In order to get these answers a question form was developed and sent to thesuppliers to BioCentrum. In this form they were to respond to the quantity suppliedto BioCentrum and the amount of energy was spent when manufacturing thecomponents.

In today?s modern age, energy consumption has become a major issue, both from an environmental viewpoint and cost perspective. Because of a rapid technologic change and increased costs of production of electricity, the demand to develop effective methods for energy efficiency industries have grown.The electricity-intensive industries, such as plastic industry, the demand to reduce energy consumption has grown significantly over the past 10 years, which have led to the development of different methods to determine and locate energy-consuming parts in the industry. This also means being able to prioritize and organize activities in the industry.In this study the measurements of voltage, current, power and PF performance on injection molding machines (K-TEC 275 form Ferromatik Milacron in Germany) with a focus to locate, within a machine, various measures that could improve energy use in the plastics industry, in this case RostiGP in Gislaved. These measurements have been carried out with the help of a power quality clamp meter to carry out time logs of the machines for some time during normal word rate.

The society strives for sustainable development, in the construction industry it is expressed through sustainable building. Energy and LCC analyzes increases the ability to make conscious decisions in the process. A problem in the construction industry is that energy and LCC analysis is not used to the desired extent, as they are perceived as complicated and time consuming. The report aims to achieve a more sustainable building through increased use of energy and LCC analyzes.The goal is to show how BIM can be used to improve the efficiency of the energy and LCC analyzes.The study was conducted with a literature review and a case study to answer which information that is required in a BIM model to perform energy and LCC analyzes. The study also shows which software can be used in BIM based energy and LCC analyzes and how the analyzes can be carried out efficiently.The result shows that effective analyzes may be performed if the BIM-model contains the relevant information for making analyzes.

Being able to predict the future had been an invaluable competitive advantage for any corporation. Forecasting is a vital part of any business, hence a good forecast allows enterprises to invest in a beneficial way. However, there are several ways to prepare forecasts and the forecast methodology can vary. An industry that is dependent on forecasts is the Energy industry. By predicting consumers' energy consumption, Swedish energy companies can hedge on the Nordic power market Nord Pool.

A large proportion of the energy consumption is in the building industry and a large part goes to heating our homes and premises. In the developing countries' development now threatens the large consumption of energy in our earth's climate. It is in the West world that we must be good role models in terms of energy efficiency. One solution to reduce energy consumption for heating of buildings may be to continue to build low energy houses and passive houses, but it is also about rebuilding the buildings that currently have high energy consumption such as the old Million program Houses. These buildings will be standing many years and their energy consumption will not diminish over time by itself and energy prices will certainly not diminish in the future.

This study tests two financial valuation models empirically by valuing three stocks from three industries, with the purpose of studying how well valuation models work empirically and to make a forecast. The models which will be tested are residual income valuation and discounted cash flow. Nine stocks will be picked strategically from the Swedish stock market and additional analysis will follow in the analysis chapter.Based on analysis and valuation, the commodities industry has decent valuation as the healthcare industry is undervalued thanks to the high valuation of AZN. The Energy industry has low value due to the capital intensive nature of the industry. When it comes to the models and their practical implementation, DCF has been the most problematic to apply empirically whereas RIV was better but it still shows extreme values, which teaches the student the clear difference between theory and empiri..

Energy is today a very common topic, not only in Sweden but in the whole Europe. In EU they have given out a directive 2002/91/EG about buildings energy use and throw this they have forced their members to show how much energy their buildings use. In Sweden has the gouvernment established a law (SFS 2006:985) about energy declaration for buildings which demands that the building owner needs to show how much their buildings energy consumption are. Important to know is that this law doesn´t applies for industrial buildings.The report will show what the new law about energy declaration for buildings and appurtenant directions will mean for Riksbyggen. Also energy calculations will be done to be able to compare Riksbyggen buildings with the new law and directions.

Everyone has to take a greater responsibility in energy issues, both individuals and companies. There have been some major developments in the construction industry but there is still a lot to be done. This diploma work thesis presents different methods of making existing construction shed establishments to use less energy. What is possible to do and how much energy is there to be saved? A shed establishment consisting of 8 shed units were studied in this project and the building simulation tool VIP-Energy was used to simulate different types of material in the sheds. An infrared camera was used to locate thermal bridges. There are several factors that can be improved to make a construction shed establishment to use less energy.

This diploma work on D-level is made in cooperation with Varnäsföretagen AB in Eskilstuna. The company performs contract manufactured aluminium goods. This work is a continuation on earlier diploma work in Varnäsföretagen AB. Even if the industry process consumes much energy for melting the aluminium goods, they consume a great amount of oil to warm up the building. The purpose of this work is to examine some places in the building and the process to see how much energy it is possible to recycles to the heating system and reduce the costs for heating.